手持式合金分析儀操作規程中英文版

文章出處：未知人氣：發表時間：2016-03-07

（1）手持式合金分析儀操作規程中文版

一、范圍
本規程適用于廠內型號為Niton XLT898W手持式合金分析儀的使用操作。

二、工作原理及適用范圍：

采用X射線熒光（XRF）技術進行多元素分析。用于各種高低合金鋼、不銹鋼、工具鋼、鉻/鉬鋼、鎳合金、鈷合金、鎳/鈷耐熱合金、鈦合金、銅合金等，可分析Ti V Cr Mn Fe Co Ni Cu Zn Nb Zr Mo Ag Pd Sn Hf Ta W Re Pb Bi Se Sb 等元素。

三、工作條件：

工作溫度：-20℃-50℃；樣品溫度：0℃-50℃。
四、被測金屬樣品的外形尺寸

線材：直徑1mm以上；

小口徑管材：外徑2mm以上；

被測材料與探測窗之間的距離小于10mm；

被測材料（表面）的狀態：平面、曲面、粗糙表面、不規則表面、粉末狀、振動狀態等。被測表面應打磨露出金屬光澤，不影響分析結果。

六、注意事項：

1. 本儀器需專人操作，專人負責日常維護、清潔及保養工作，并做好儀器使用記錄。非相關人員不得擅自操作。 2. 操作前應確保電池有足夠電量。

3. 在任何時候都要確定X射線方向、謹防輻射。 4. 在任何情況，如果未使用儀器，不得開啟擋板。

5. 在測試過程中不得將儀器放在Kapton窗口附近。在擋板開啟時，勿將儀器指向自己或其他任何人。

6. 在下載讀數時不可進行測量，在刪除數據時切勿關閉儀器。 7. 勿將儀器侵入水中。

8. 本儀器因采用X射線熒光,因而要避免在露天強光（特別是紫外線強的前提下）操作，以免數據不準。

9. 本儀器為精密設備，操作時盡量做到輕拿輕放，以免設備破損。

七、其他關于儀器的工作原理、保養、故障排除等內容請參閱具體說明書或聯系設備廠家。

（2）手持式合金分析儀操作規程英文版

1、. Range

This operating regulation is applied for handy-alloy analysis in HBG named Niton XLT898W.

2. Working principle and scope of application

Using fluorescent X-ray technology to have multi-element analysis. this devie is applied for kinds of alloyed steel, non-corrosive steel, tool steel, chrome-molybdenum steel, nickel alloy, cobalt alloy, nickel/cobalt heat-resisting alloy, titanium alloy, copper alloy and so on. it can also analysis kinds of elements like Ti V Cr Mn Fe Co Ni Cu Zn Nb Zr Mo Ag Pd Sn Hf Ta W Re Pb Bi Se Sb.
3.Working condition

Working temperature: -20℃-50℃;specimen temperature: 0℃-50℃.

4、outline dimension of measured metal specimen

Wire stock: diameter greater than 1mm;

Small pipe-tube: external diameter greater than 1mm;

Distance between measured material and detecting window less than 10mm;

Status of measured material(surface):flat face, curved face, rough face, irregular face, pulverous face, vibrate face and so on, measured material surface should be shined until the material appear metal brightness and not effect on analysis result.
5.Operation procedure:

1. Reading the operation standard or operation instruction of this device carefully before using, examining the device surface carefully, Replacing the device immediately if any abnormal phenomenon or breakage was found.

2. Wearing device proofing girdle before using, antiskid belt should be grabbed in wrist when grab the device in case of damaging.

3. Metal brightness should be appeared before measurement. Pressing the battery button, then the device come out a present sound. After the liquid crystal screen manifests record, press 1 2 3 4 E in the touch screen to get in operation interface.

4. Device adjustment: before formal testing, testing block should be tested, the product should not be testing until the record was normal.

5. The detective window should near the measured product surface when the measurement is begin, press the detecting button in grip, when working light is flashing the measurement begin, it is over when the device comes out sound. 6. Pressing “▼”/“▲”to observe detection record. Pressing the detecting button again if you want to continue detection. Pressing “←”to quit detection interface.

7.Holding on pressing power button when measurement was complete, and the device should be located in water-proof instrument case.
6. matters needed attention:

1.This device need specialized operator and specialized individual to maintain, cleaning daily, Device record should be written down and other people without permission should not use this device.

2. Ensure enough battery before operation.

3. Ensure the derection of X-ray whenever using it. Being aware of radiation. 4. Under any circumstance, baffle must not be opened if the device was not used.

5. The device should not located near the Kapton window during the testing phase. When baffle is open, the device should not opoint to youself or others.

6.No testing when the record is downloading and No shutting down the device when deleting the record.

7. The device should not immerse into water.

8. Own to the device using X-ray, the device should avoid out-door operation(especially in the day when ultraviolet ray is high),in case of inaccuracy record.

9. This device is a precise instrument, when operating it should place softly in case of damage.
7. Other information about the working principle, maintainance, failure recovery and so on should be found in the instruction or factory which product this device.

下一篇：6500-RoHS和消費者安全分析儀上一篇：設備采購合同的基本要素有哪些

手持式合金分析儀操作規程中英文版

（1）手持式合金分析儀操作規程中文版

（2）手持式合金分析儀操作規程英文版

推薦產品

同類文章排行

最新資訊文章